AnsweredAssumed Answered

pairvolchk error

Question asked by Vijeta Bhedi on Nov 12, 2015
Latest reply on Oct 3, 2018 by Johnson Berry

Like • Show 0 Likes0
Comment • 6

hello Team,

I am having below error while executing the pairvolchk command

Checking replication status

pairvolchk -ISI1000 -g HR4UARW_PP_COW -ss

pairvolchk : execution error.

pairvolchk: [EX_CMDRJE] An order to the control/command device was rejected

Refer to the command log(/HORCM/log1000/horcc_frhdstdrpvcci01.log) for details.

07:05:53 - pairresync -ISI1000 -g HR4UARW_PP_COW

pairresync: [EX_ENLDEV] No such LDEV within the RAID

Refer to the command log(/HORCM/log1000/horcc_frhdstdrpvcci01.log) for details.

Take_Snap - KO: Could not resync HR4UARW_PP_COW, please check !

I am able to pairdisplay only after horcm service restarted.

No one else has this question

Outcomes

6 Replies

Yury Yavorsky Nov 12, 2015 2:45 AM
Mark Correct
Correct Answer
seems like it was problem with command device. If i get it right currently you are able to perform operations. What do you need then?
Like • Show 0 Likes0
Actions
- Vijeta Bhedi @ Yury Yavorsky on Nov 12, 2015 3:02 AM
  Mark Correct
  Correct Answer
  Thank you Yury , but if it is related to Comand device then it woould have not run after restarting the horcm service.
  Like • Show 0 Likes0
  Actions
  - Yury Yavorsky @ Vijeta Bhedi on Nov 12, 2015 7:03 AM
    Mark Correct
    Correct Answer
    Maybe it was some intermitent error accessing CMD. Anyway it is hard to investigate when the error has gone)
    Like • Show 0 Likes0
    Actions
Pat Barone Dec 23, 2017 8:02 AM
Mark Correct
Correct Answer
In my case I can run the pairdisplay command but not pairresync even after stopping and restarting horcm service.
Any ideas?
# pairresync -IM0 -g PSS_SI
pairresync: [EX_CMDRJE] An order to the control/command device was rejected
Refer to the command log(/HORCM/log0/horcc_yogi.log) for details.
It was rejected due to SKEY=0x05, ASC=0x26, ASCQ=0x00, SSB=0xB9A0,0x2301 on Serial#(350095)
Like • Show 0 Likes0
Actions
- Vinod Subramaniam @ Pat Barone on Dec 23, 2017 8:48 AM
  Mark Correct
  Correct Answer
  2301 The pair operation was rejected because shared memory is not allocated
  Like • Show 0 Likes0
  Actions
Johnson Berry Oct 3, 2018 11:47 AM
Mark Correct
Correct Answer
You can use this command-
# pairvolchk -g
Printer in error state
pairvolchk : Volstat is P-VOL.[status = PAIR fence = ASYNC CTGID = 2]
# pairvolchk -g
pairvolchk : Volstat is P-VOL.[status = PAIR fence = DATA ]
# pairvolchk -g oradb
pairvolchk : Volstat is P-VOL.[status = PAIR ]
# pairvolchk -g oradb
pairvolchk : Volstat is P-VOL.[status = PAIR CTGID = 1]
Like • Show 0 Likes0
Actions

Jive

Hitachi Vantara Community

pairvolchk error

Outcomes

Related Content

Recommended Content